Os-engines 65AX Manual do Utilizador

It is of vital importance, before attempting to operate your engine, to read the general 'SAFETY INSTRUCTIONS AND WARNINGS' section

18The exhaust outlet of the silencer can be rotated to any desired position in the following manner:Loosen the locknut and assembly screw.Set the exha

20Suggested fuel tank capacity is approx 350cc. This will allow 10-12 minute flights.FUEL TANK LOCATIONMake sure that the tank is well rin

22MIXTURE CONTROLSThe Needle ValveWhen set to produce maximum power at full throttle, this establishes the basic fuel/air mixture strength. The c

24! STARTINGBe sure to use an electric starter to start the engine.Fill the fuel tank with fuel. When filled, prevent fuel flowing into

26Attention :Do not choke the carburetor air intake when applying the starter. This could cause an excessive amount of fuel to be draw

28During subsequent flights, the needle-valve can be gradually closed to give more power. However, if the engine shows signs of running

30IDLING ADJUSTMENT CHARTStart the engine.Make sure that the throttle isfully open.Adjust the needle-valve.Close the throttle gradually.Set the idle s

32REALIGNMENT OF MIXTURE CONTROL VALVESUBSEQUENT STARTING PROCEDUREOnce the optimum needle-valve setting has been established (see page 29,

34123SymptomFactorCauseCorrective actionRecharge the electric starter battery.Recharge lead-acid cell or replace dry battery. (Note: An unused, or alm

36CARE AND MAINTENANCEPlease pay attention to the matters described below to ensure that your engine serves you well in regard to performan

2Remember that your engine is not a "toy", but a highly efficient internal-combustion machine whose power is capable of h

38ENGINE EXPLODED VIEWC.M3x1621345678910121113141516C.M3x81-1Type of screw C...Cap Screw 7987111079871160M3x8M3x16CAP SCREW SETS(10pcs./sets)Code No.S

40CARBURETOR EXPLODED VIEW12457S.M3X3363-13-27-17-289N.+M3.5x6N.+M3x67-37-47-51-1Type of screw N...Round Head Screw S...Set Screw41CARBURETOR PARTS L

42(71905200)(73101010)O.S.GLOW PLUGO.S. GENUINE PARTS & ACCESSORIESRADIAL MOTOR MOUNTSILENCER EXTENSIONADAPTORS(45024000)SPINNER NUT5/16"-24L

44156 g / 5.50 oz.Displacement Bore Stroke Practical R.P.M. Power output WeightSPECIFICATIONSDimensions(mm)THREE VIEW DRAWINGE-4010A Silencer Assembl

4NOTESThis engine was designed for model aircraft. Do not attempt to use it for any other purpose.Mount the engine in your model se

6NOTESAdjust the throttle linkage so that the engine stops when the throttle stick and trim lever on the transmitter are fully retarded. A

8NOTES WHEN APPLYINGAN ELECTRIC STARTERDo not over-prime. This could cause a hydraulic lock and damage the engine on application of the elect

10BASIC ENGINE PARTSCylinder headCarburetor Type 61D CrankshaftPropeller nutPropeller washerDrive HubCrankcaseCover PlateGlowplugBeam Mount11Tools, a

12FUELThe 65AX should be operated on a methanol based fuel containing not less than 18% (volumetric) castor oil, or a top quality synthetic lubricant

148mmTOOLSHEX ScrewdriverSCREWDRIVERNecessary for engine installation.1.5mm, 2.5mmNecessary for carburetor adjustments.Phillips ScrewdriverNo.2, etc.S

16How to fasten the mounting screws.Hardwood mounting beamsRadial motor mount (cast aluminum)Tighten second nutfirmlydown onto first nut.Tighten this