Os-engines 21RZ-V01B (P) Manual do Utilizador

It is of vital importance, before attempting to operate your engine, to read the general 'SAFETY INSTRUCTIONS AND WARNINGS' section on pages

ASSEMBLY1. ¡ ¡ ¡ 2. Install the element. ¡ ¡ ¡ Slide the element base over the center tube (See Fig.1) and press down.If it is tight

INSTALLATION1.2.3. ¡ ¡ REPLACEMENT OF ELEMENT1.2. ¡ Apply instant setting glue to the joint be-tween the air cleaner and the intake elbow and

FURTHER PRECAUTIONSWhen removing the air cleaner, check the inside of the center tube and carburetor venturi. If any dirt is detected, this indicates

Apart from when actually burned out, a plug may need to be replaced because it no longer delivers its best performance, such as when:When to replace t

BATTERY LEADSLONG SOCKET WRENCHThese are used to conduct current from the battery to the glowplug. For convenience, special leads with a suitable clip

•••Use the same fuel as is to be employed for all initial running and containing NOT LESS THAN 18% lubricant. STARTING THE ENGINE & RUNNING-IN (&a

It is vitally important to set the throttle at the correct position before starting the engine. If the engine is allowed to run with the throttle too

IF THE ENGINE FAILS TO STARTCheck the following:Glowplug battery discharged or glowplug defunct.Fuel not reaching carburetor.Engine flooded. Do not ov

Warning!Mixture adjustments (whether via the Mixture Control Valve, or the Needle-Valve) cannot be made accurately under 'no-load' condition

REALIGNMENT OF MIXTURE CONTROL VALVE In the course of making carburetor adjustments, it is just possible that the Mixture Control Valve may be inadver

CONTENTSSAFETY INSTRUCTIONS AND WARNINGS ABOUT YOUR O.S. ENGINEINTRODUCTION, BASIC ENGINE PARTSINSTALLATION AIR CLEANERGLOWPLUGTOOLS, ACCESSORIES, etc

Warning!Do not attempt to turn the engine with the starter if the engine is over-primed (flooded) with fuel. To do so is likely to seriously damage th

GUARANTEEThis engine is constructed from the very best materials available and to the very highest engineering standards, using the most advanced prec

Displacement Bore Stroke Practical R.P.M. Power output Weight ( ) -01b(P)SPECIFICATIONSTHREE VIEW DRAWING Dimensions(mm)3.46 cc(0.211cu.

EXPLODED VIEWType of screw C…Cap Screw M…Oval Fillister-Head ScrewF…Flat Head Screw N…Round Head Screw S…Set Screw 4321C.M2.6X7C.M2.6X15ewq=w-2w-1

ENGINE PARTS LISTThe specifications are subject to alteration for improvement without notice. Center Tube Intake Elbow Center Screen Element Plate Set

-09876543-23-1321-21-11C.M2.6X7The specifications are subject to alteration for improvement without notice.Type of screw C…Cap Screw M…Oval Fillister

RACING ENGINE PARTS(72106030) (71530200)(71521000)(71608001)No.8(71605100)A5GLOW PLUG No.8/A5T-2030 TUNED SILENCERSUPER JOINT TUBE 21CRANKSHAFT CLAMP

MEMO26

C Copyright 2001 by O.S.Engines Mfg. Co., Ltd. All rights reserved. Printed in Japan.060100TEL. (06) 6702-0225FAX. (06) 6704-27226-15 3-Chome Imagawa

Remember that your engine is not a "toy", but a highly efficient internal-combustion machine whose power is capable of harming you, or other

WARNINGSModel engine fuel is poi-sonous. Do not allow it to come into contact with the eyes or mouth. Always store it in a clearly marked container an

This engine is intended for model cars. Do not attempt to use it for any other purpose.Mount the engine in your model securely, following the manufact

NOTESTo stop the engine, fully retard the throttle stick and trim lever on the trans-mitter, or, in an emergency, cut off the fuel supply by pinching

BASIC ENGINE PARTSSILICONE TUBING AND O-RINGSBefore installing the engine on the chassis:1.2.Fit the exhaust seal ring supplied.The MAX-21RZ-V01b and

ENGINE INSTALLATIONMake sure that the vehicle's engine mounting surfaces are level and in the same plane. Poor installation may cause distortion

AIR CLEANER TYPE 201This is a heavy-duty wet type air cleaner that has been developed specifically for 3.5cc 'off-road' model car engines. I